Paper Spool Humidity Creep Curve Versus PP Reels

A paper spool humidity creep curve plots deformation against elapsed exposure time at a stated relative humidity, with a PP ... Ask Mingskye for a sample.

A paper spool humidity creep curve plots deformation against elapsed exposure time at a stated relative humidity, with a PP reference measured on the same rig. Record deformation at fixed time steps, divide by the initial dimension to get strain, and plot strain against time for both materials. A worked example with illustrative readings shows the comparison. Use the slope, not a single point, when you set a maximum dwell time before winding or despatch.

This page covers paper spool humidity creep curve in six sections: Checking against rack and floor ratings; Drawing the load path before calculating; Converting mass and energy units explicitly; Measuring a property before conditioning; Capping the combined factor at a floor; Keeping humidity, temperature and cycles separate. Each section answers one practical question and can be read on its own.

paper spool humidity creep curve - PP hollow sheet cable reel sizing reference from Mingskye

Key facts

  • A computed stack height must clear the rack and floor ratings before it is adopted.
  • A load calculation starts with a sketch of how force travels from the cable pack into the reel.
  • Mass and energy conversions are simple but must be recorded in full.
  • A derating factor starts with a dry or reference-state measurement.
  • A floor stops a combined product from falling to an unusable value.

Checking against rack and floor ratings

A computed stack height must clear the rack and floor ratings before it is adopted.

Convert the bottom-layer load into a load per rack position and per square metre, then compare both with the published ratings for your storage system. A volume gain that exceeds either rating is not usable.

Record the rating source and date. Storage equipment is replaced over time, and an old rating should not govern a new fleet.

  • Convert to per-position and per-area loads
  • Compare with both ratings
  • Record rating source and date

Drawing the load path before calculating

A load calculation starts with a sketch of how force travels from the cable pack into the reel.

Mark the wound pack, the flange, the flange-to-core joint, the hub and the support points. Each arrow on that sketch becomes one term or one boundary condition in the arithmetic.

Change the sketch and the equation changes. A flange loaded by a static stack of reels and one loaded by outward cable pressure are not the same case and should not share a result.

  • Sketch the load path first
  • Map each arrow to a term
  • Separate static and wound-pack cases

For terminology and test-method context see ISO standards catalogue. The guidance on this page is practical handling guidance, not a test report or a certificate.

Converting mass and energy units explicitly

Mass and energy conversions are simple but must be recorded in full.

Convert kilograms to tonnes by dividing by one thousand, and kilowatt hours to megajoules by the stated conversion, before applying a factor. Keep the original value in a separate column.

A misplaced factor of one thousand is easy to miss in a plausible-looking total. Recording both the original and the converted value makes the check trivial.

  • Keep original and converted columns
  • State the conversion ratio used
  • Check the magnitude of the result
Environment question Short answer Derating factor In this guide
What should be checked about checking against rack and floor ratings? A computed stack height must clear the rack and floor ratings before it is adopted. Convert the bottom-layer load into a load per rack position and per square metre, then … Section 1
What should be checked about drawing the load path before calculating? A load calculation starts with a sketch of how force travels from the cable pack into … Mark the wound pack, the flange, the flange-to-core joint, the hub and the support points … Section 2
What should be checked about converting mass and energy units explicitly? Mass and energy conversions are simple but must be recorded in full. Convert kilograms to tonnes by dividing by one thousand, and kilowatt hours to megajoules by … Section 3
What should be checked about measuring a property before conditioning? A derating factor starts with a dry or reference-state measurement. Measure the chosen property at a stated temperature and humidity, on a defined sample and … Section 4

Measuring a property before conditioning

A derating factor starts with a dry or reference-state measurement.

Measure the chosen property at a stated temperature and humidity, on a defined sample and test method. Record the value, the date and the conditioning state.

Without a reference state there is no denominator for the factor. A reference measured on a sample that has already absorbed moisture makes the factor meaningless.

  • State temperature and humidity
  • Record the conditioning state
  • Keep the reference value with its date

Capping the combined factor at a floor

A floor stops a combined product from falling to an unusable value.

Set a minimum combined factor from your handling or line constraints, then take the larger of the computed product and that floor. Record the floor and its justification.

A product of many small fractions can collapse to a figure no operation can use. The floor turns that into an explicit decision rather than an arithmetic artefact.

  • Set the floor from a real constraint
  • Take the larger of product and floor
  • Record the justification

Keeping humidity, temperature and cycles separate

Three derating mechanisms are computed separately before they are combined.

Humidity acts on moisture uptake, temperature on dimensional and stiffness change, and cycles on accumulated damage. Compute each factor from its own test before multiplying them.

Measuring one combined factor on a single sample hides which mechanism is responsible. A targeted fix then becomes impossible.

  • Compute one factor per mechanism
  • Source each from its own test
  • Combine only at the final step

Frequently asked questions

Why plot strain instead of raw deformation?

A computed stack height must clear the rack and floor ratings before it is adopted. Convert the bottom-layer load into a load per rack position and per square metre, then compare both with the published ratings for …

Which conditions must match between materials?

A load calculation starts with a sketch of how force travels from the cable pack into the reel. Mark the wound pack, the flange, the flange-to-core joint, the hub and the support points. Each arrow on that sketch becomes one …

What does the slope control?

A derating factor starts with a dry or reference-state measurement. Measure the chosen property at a stated temperature and humidity, on a defined sample and test method. Record the value, the date …

How is the comparison kept fair?

Three derating mechanisms are computed separately before they are combined. Humidity acts on moisture uptake, temperature on dimensional and stiffness change, and cycles on accumulated damage. Compute each factor from its own …

Sources and further reading

  • ISO standards catalogue: packaging, transport and plastics test methods — www.iso.org
  • ASTM International: standard test methods for plastics and packaging — www.astm.org
  • PlasticsEurope: polypropylene material properties and recycling information — plasticseurope.org
  • BIPM SI Brochure: units, prefixes and rules for expressing measured quantities — www.bipm.org

References checked by publisher and title on 2026-11-17. Standards and regulations are cited by name only; no performance values are attributed to them. Every figure and every worked example in the text uses illustrative input values, not measured product data; substitute your own measured inputs and verify them against your supplier’s current data sheet and a trial before use. Confirm applicability and current versions for your own operation before relying on any of them.

Related Mingskye cable reels

For a quotation, a sample reel or help substituting your own cable diameter, winding length, stack height and return route into these calculations on site, contact service@mingplastics.com or WhatsApp +86 189 3887 1524. Include the cable type, the destination, the expected cycles per year and the figures your finance and sustainability teams need to defend so the recommended specification can be confirmed before you order.

Final takeaway

For paper spool humidity creep curve, Apply one derating factor per environmental variable and show the combined factor in the final line. Three derating mechanisms are computed separately before they are combined.