{"id":6916,"date":"2026-10-28T06:27:24","date_gmt":"2026-10-28T06:27:24","guid":{"rendered":"https:\/\/www.mingplastics.com\/pp-honeycomb-protection-board-glass-curtain-wall-install.html"},"modified":"2026-10-28T06:27:24","modified_gmt":"2026-10-28T06:27:24","slug":"pp-honeycomb-protection-board-glass-curtain-wall-install","status":"publish","type":"post","link":"https:\/\/www.mingplastics.com\/fr\/pp-honeycomb-protection-board-glass-curtain-wall-install.html","title":{"rendered":"PP Honeycomb Protection Board for Glass and Curtain Wall: Protect Glazing During Installation"},"content":{"rendered":"
\"PP<\/a><\/div>\n

Glazing is one of the few building elements where a scratch is a replacement rather than a repair, and curtain wall units arrive on site early enough to be exposed to everything that follows. This article looks at protecting glass and glazed assemblies during installation and fit-out. The focus is scratch prevention, edge protection and choosing a board that will not mark or bond to the glass.<\/p>\n

A scratched unit is a replaced unit<\/h2>\n

Glass cannot be polished out, so the cost of damage is the unit plus the crane or access time to replace it. That makes protection a straightforward calculation on any glazed project.<\/p>\n

Damage usually comes from contact: tools, ladders, scaffold components and cleaning equipment rather than from load. So the protection needs to be a physical barrier that stays in place and does not itself abrade the glass.<\/p>\n

A rigid PP honeycomb protection board<\/a><\/a> gives that barrier. With a felt or fleece facing it cannot scratch the glass, and because it is loose-laid it avoids the adhesive residue problem that glazing manufacturers warn about.<\/p>\n

Thickness choices from 2 mm to 12 mm<\/h2>\n

For glazing the decision is usually about rigidity and coverage rather than load: within the 2 mm to 12 mm range, a board stiff enough to stand against the opening without bowing into the glass is what protects.<\/p>\n

Thin boards suit small areas and short programmes. Thicker boards suit site hoarding conditions, repeated handling and where panels must span an opening without support.<\/p>\n

\n\n\n\n\n\n\n\n\n
Board group<\/th>\nTypical thickness<\/th>\nWhere it earns its place<\/th>\nWatch-outs<\/th>\n<\/tr>\n<\/thead>\n
Light-duty panel<\/td>\n2-3 mm<\/td>\nSmall glazed areas, short programmes, indoor<\/td>\nBows into openings if unsupported<\/td>\n<\/tr>\n
General glazing panel<\/td>\n4-6 mm<\/td>\nInstalled units with trades working around them<\/td>\nRestraint must not contact the glass<\/td>\n<\/tr>\n
Heavy-duty panel<\/td>\n8-10 mm<\/td>\nSite hoarding conditions, repeated handling<\/td>\nHeavier panels at height; plan manual handling<\/td>\n<\/tr>\n
Maximum protection<\/td>\n12 mm<\/td>\nExposed elevations, long programmes, high wind<\/td>\nMore than short indoor work needs<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n

Edge protection and avoiding adhesive contact<\/h2>\n

Protect the edges and corners of units as well as the face, because chips at the edge are as disqualifying as a scratch across the pane.<\/p>\n

Avoid anything with adhesive contact on the glass. Use loose-laid panels and mechanical or independent restraint rather than tape on the glazing surface.<\/p>\n

Keep the protection clear of weep holes and drainage paths in curtain wall systems so that water management is not blocked during the works.<\/p>\n

How honeycomb board compares with film, cardboard and ply<\/h2>\n

Applied glazing films are designed for glass and work well, but they are single-use, must be removed within a stated period and can leave residue if left too long.<\/p>\n

Cardboard and ply protect against contact but are heavy, absorb water and can themselves mark frames and gaskets. They also blow about on exposed elevations.<\/p>\n

A PP honeycomb board is light, water-resistant and re-usable, and with a soft facing it will not scratch glass. It suits the period after installation when trades are still working around the glazing.<\/p>\n

A practical trial plan for glazed areas<\/h2>\n

Protect one elevation or zone and leave a comparable one on the current method. Inspect at fixed intervals for scratches, edge chips and frame damage, photographing with consistent lighting and angle.<\/p>\n

Run a contact test: bring the tools or equipment that typically touch the glazing into contact with a sample panel, then check the glass behind it.<\/p>\n

Record whether panels stayed in place in wind and whether any fixings contacted the glass, because on elevations those two factors decide the outcome.<\/p>\n

What to include in a protection board enquiry<\/h2>\n

State the glazing type, unit sizes, whether frames are powder coated or anodised, and the access conditions. Ask for the recommended thickness, facing, panel size and fire performance.<\/p>\n

Confirm that the system is loose-laid and non-adhesive, and ask for guidance on restraint without contacting the glass. Custom sizes reduce cutting around large units.<\/p>\n

For a quotation or sample panel, contact service@mingplastics.com<\/a> or WhatsApp +86 189 3887 1524<\/a>. Include the surface type, floor area, trades on site and expected duration so the recommended thickness, facing and fire performance can be confirmed before you order.<\/p>\n

Final takeaway<\/h3>\n

Glazing protection is a contact barrier problem, not a load problem. Use a soft-faced, loose-laid panel, protect edges and weep paths, and restrain without touching the glass.<\/p>","protected":false},"excerpt":{"rendered":"

Scratched glass is replaced, not repaired. This guide covers thickness from 2 mm to 12 mm, non-adhesive restraint, edge protection and a glazing trial plan.<\/p>","protected":false},"author":1,"featured_media":0,"comment_status":"","ping_status":"","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[],"class_list":["post-6916","post","type-post","status-publish","format-standard","hentry","category-uncategorized"],"blocksy_meta":[],"_links":{"self":[{"href":"https:\/\/www.mingplastics.com\/fr\/wp-json\/wp\/v2\/posts\/6916","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.mingplastics.com\/fr\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.mingplastics.com\/fr\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.mingplastics.com\/fr\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.mingplastics.com\/fr\/wp-json\/wp\/v2\/comments?post=6916"}],"version-history":[{"count":0,"href":"https:\/\/www.mingplastics.com\/fr\/wp-json\/wp\/v2\/posts\/6916\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.mingplastics.com\/fr\/wp-json\/wp\/v2\/media?parent=6916"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.mingplastics.com\/fr\/wp-json\/wp\/v2\/categories?post=6916"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.mingplastics.com\/fr\/wp-json\/wp\/v2\/tags?post=6916"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}