{"id":6904,"date":"2026-10-28T06:02:37","date_gmt":"2026-10-28T06:02:37","guid":{"rendered":"https:\/\/www.mingplastics.com\/pp-honeycomb-protection-board-hardwood-floors-renovation-scratches.html"},"modified":"2026-10-28T06:17:12","modified_gmt":"2026-10-28T06:17:12","slug":"pp-honeycomb-protection-board-hardwood-floors-renovation-scratches","status":"publish","type":"post","link":"https:\/\/www.mingplastics.com\/fr\/pp-honeycomb-protection-board-hardwood-floors-renovation-scratches.html","title":{"rendered":"PP Honeycomb Protection Board for Hardwood Floors: Stop Renovation Scratches Before They Start"},"content":{"rendered":"
\"PP<\/a><\/div>\n

Hardwood is usually the most expensive surface in a renovation and one of the last to be finished, which means it has to survive weeks of foot traffic, ladders, tool drops and paint spills before the client ever walks on it. A protection board is the cheapest insurance on that schedule, but only if the board is specified for the load it will actually see. This article looks at hardwood floor protection during renovation and turns it into a specification checklist for contractors, fit-out teams and facility managers. The focus is scratch prevention, load spreading and a board that survives being walked on every day.<\/p>\n

Why hardwood protection deserves a specified board, not a roll of paper<\/h2>\n

A rolled paper or thin film layer is bought because it is cheap and familiar, then replaced several times as it tears, shifts or soaks through. The replacement cost is labour, not material: somebody has to clear the room, sweep, re-lay the sheet and tape it again. On a multi-week interior job that repeated cycle is what quietly damages the floor, because the floor is unprotected during every replacement window.<\/p>\n

A rigid PP honeycomb protection board<\/a><\/a> behaves differently. The polypropylene core spreads a point load across a wider area, so a ladder foot or a tool case does not concentrate its weight on one spot. The felt or fleece facing keeps the contact side from abrading a finished surface. Because the board is a panel rather than a film, it stays where it is laid instead of creeping under boots.<\/p>\n

For hardwood specifically, the two failure modes that matter are abrasion from grit trapped under the protection and indentation from concentrated loads. A board that does not move solves the first; a board thick enough to spread load solves the second. Both are specification questions, not brand questions, and both can be checked before the order is placed.<\/p>\n

Thickness choices from 2 mm to 12 mm<\/h2>\n

The thickness schedule should be read as a set of jobs, not as one universal protection board specification. The product range covers 2 mm to 12 mm, and the right value depends on what crosses the floor and how long the protection has to stay down. Ask the supplier to tie the quotation to a thickness, a facing material and an expected traffic level rather than to a generic heavy-duty claim.<\/p>\n

Thin boards are easier to cut and carry, and they suit walls, joinery and light foot traffic. Thicker boards resist indentation from concentrated loads such as scaffold feet, pallet trucks and appliance trolleys. The felt facing is the part that touches the finish, so on a polished or lacquered surface the facing matters as much as the core thickness.<\/p>\n

\n\n\n\n\n\n\n\n\n
Board group<\/th>\nTypical thickness<\/th>\nWhere it earns its place<\/th>\nWatch-outs<\/th>\n<\/tr>\n<\/thead>\n
Light-duty panel<\/td>\n2-3 mm<\/td>\nWalls, joinery, cupboard fronts, light foot traffic<\/td>\nWill dent under trolley or scaffold point loads<\/td>\n<\/tr>\n
General floor panel<\/td>\n4-6 mm<\/td>\nFinished hardwood, laminate and tile under normal site traffic<\/td>\nSeams must be taped or they collect grit<\/td>\n<\/tr>\n
Heavy-duty panel<\/td>\n8-10 mm<\/td>\nAppliance moves, pallet trucks, repeated loaded crossings<\/td>\nHeavier to carry; plan the handling, not just the spec<\/td>\n<\/tr>\n
Maximum protection<\/td>\n12 mm<\/td>\nScaffold feet, plant moves, long-duration public routes<\/td>\nOver-spec for simple painting work and adds handling cost<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n

How honeycomb board compares with paper, film and plywood<\/h2>\n

Corrugated paper and polyethylene film are the default because they are cheap per square metre and available everywhere. Their weakness is that they are consumables: once torn or soaked, the protection is gone and the waste leaves the site as a mixed-material bin. On a long job the accumulated waste and re-labour usually exceed the price difference.<\/p>\n

Plywood or MDF sheets protect well and are re-usable, but they are heavy, awkward to cut on site, and they can mark a floor if grit is trapped underneath. They also absorb water, which is a problem on projects where wet trades are still working.<\/p>\n

A PP honeycomb board sits between the two. It is a panel, so it resists tearing and stays in place, but it is light enough for one person to carry and cut. It does not absorb water, which matters when the board has to survive wet trades, cleaning and outdoor transitions. The trade-off is that a plastic board is a purchased asset rather than a consumable, so it only pays back if it is actually collected and re-used.<\/p>\n

Reuse, cleaning and cost per project<\/h2>\n

The reuse case is straightforward but only works with a routine. Boards should be lifted, brushed or wiped, stacked flat and stored dry between phases. If they are left on site until the end and then binned, the board has been bought as an expensive single-use sheet and the cost comparison will look bad against paper.<\/p>\n

A fair comparison counts cost per project, not cost per square metre. Divide the purchase price by the number of times a board is realistically re-used on your job types, add the cleaning labour, and compare that with the number of paper re-lays the same period would have needed. Teams that run repeated fit-outs, hotel refurbishments or phased retail work usually reach a payback within a few projects, because the same boards move from phase to phase.<\/p>\n

Also count the avoided remediation. A single scratched hardwood floor that has to be sanded and re-finished costs more than the protection for an entire floor plate. That is the number to put in front of a project manager who is comparing two quotes on price alone.<\/p>\n

A practical trial plan for contractors and fit-out teams<\/h2>\n

Run the trial on one floor plate that will see real traffic. Lay the specified board on half the area and keep your current method on the other half, then inspect both at the same intervals. Use the same trades, the same cleaning routine and the same inspection standard so the result is attributable to the board rather than to the room.<\/p>\n

Record three things: how many times the protection had to be re-laid, whether seams opened and let grit underneath, and the condition of the finish at handover. Photograph the same corners each time so the comparison is evidence rather than memory. If the board is re-used, record how many cycles each panel survived before it was retired.<\/p>\n

Thickness is the variable worth testing first. If a general-purpose thickness holds up on your heaviest realistic load, the lighter boards can be used everywhere else and the heavy gauge reserved for crossings and plant moves.<\/p>\n

What to include in a protection board enquiry<\/h2>\n

Describe the surface being protected, the trades that will cross it, the expected duration and whether wet trades are still on site. Ask for the thickness, the facing material, the panel size, the fire performance required by the site rules, and whether custom sizes and colours are available. Fire retardancy is a site-specification item on many commercial projects, so it should be stated in the enquiry rather than assumed.<\/p>\n

Ask how the board should be cut and joined, and what the supplier recommends for seams and edges. Edge and seam details are where most protection failures start, because that is where grit enters and where panels lift under traffic. A supplier that can answer those two questions in writing is easier to work with than one that only quotes a price per sheet.<\/p>\n

For a quotation or sample panel, contact service@mingplastics.com<\/a> or WhatsApp +86 189 3887 1524<\/a>. Include the surface type, floor area, trades on site and expected duration so the recommended thickness, facing and fire performance can be confirmed before you order.<\/p>\n

Final takeaway<\/h3>\n

A protection decision for hardwood should be based on the load, the duration and the reuse routine. Specify the thickness and facing for the heaviest realistic crossing, tape the seams so grit stays out, and only then compare prices between a reusable board and a single-use sheet.<\/p>","protected":false},"excerpt":{"rendered":"

Hardwood floors survive renovation when the protection board is specified for the real load. This guide covers thickness from 2 mm to 12 mm, felt facing, seam and grit control, reuse economics and what to put in a supplier enquiry.<\/p>","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[],"class_list":["post-6904","post","type-post","status-publish","format-standard","hentry","category-uncategorized"],"blocksy_meta":[],"_links":{"self":[{"href":"https:\/\/www.mingplastics.com\/fr\/wp-json\/wp\/v2\/posts\/6904","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.mingplastics.com\/fr\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.mingplastics.com\/fr\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.mingplastics.com\/fr\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.mingplastics.com\/fr\/wp-json\/wp\/v2\/comments?post=6904"}],"version-history":[{"count":1,"href":"https:\/\/www.mingplastics.com\/fr\/wp-json\/wp\/v2\/posts\/6904\/revisions"}],"predecessor-version":[{"id":6905,"href":"https:\/\/www.mingplastics.com\/fr\/wp-json\/wp\/v2\/posts\/6904\/revisions\/6905"}],"wp:attachment":[{"href":"https:\/\/www.mingplastics.com\/fr\/wp-json\/wp\/v2\/media?parent=6904"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.mingplastics.com\/fr\/wp-json\/wp\/v2\/categories?post=6904"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.mingplastics.com\/fr\/wp-json\/wp\/v2\/tags?post=6904"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}