Address
Building 1, No. 22, Shexi Yongping Road,
Dongguan, Guangdong, China
Work Hours
Monday to Friday: 7AM - 7PM
Weekend: 10AM - 5PM
Address
Building 1, No. 22, Shexi Yongping Road,
Dongguan, Guangdong, China
Work Hours
Monday to Friday: 7AM - 7PM
Weekend: 10AM - 5PM
The combined derating factor equation multiplies the individual factors for humidity, temperature, cycle count and handling into ... Ask Mingskye for a sample.
The combined derating factor equation multiplies the individual factors for humidity, temperature, cycle count and handling into one selection multiplier. Define each factor as a fraction of the reference limit, multiply them, then apply the product to the reference load or speed. A worked example with illustrative fractions shows why multiplying is more conservative than averaging. List each factor with its source in the same line as the result, and cap the product at a floor you choose.
This page covers combined derating factor equation in six sections: Multiplying individual factors into one product; Keeping humidity, temperature and cycles separate; Bounding the tension window with the mismatch; Floor area per thousand reels; Recording the load case with the number; Bottom layer as the design load case. Each section answers one practical question and can be read on its own.
Combined derating multiplies the individual factors rather than averaging them.
Express humidity, temperature, cycle count and handling as fractions of the reference limit, then multiply them and apply the product to the reference load or speed. An illustrative set of four fractions produces a noticeably smaller combined value than any single factor.
Multiplication assumes the effects compound. If your test data shows two effects are independent and do not stack, state that evidence before using a different rule.
Three derating mechanisms are computed separately before they are combined.
Humidity acts on moisture uptake, temperature on dimensional and stiffness change, and cycles on accumulated damage. Compute each factor from its own test before multiplying them.
Measuring one combined factor on a single sample hides which mechanism is responsible. A targeted fix then becomes impossible.
For terminology and test-method context see ISO standards catalogue. The guidance on this page is practical handling guidance, not a test report or a certificate.
A thermal mismatch narrows the usable tension window before any load is applied.
Subtract the absolute mismatch effect from the upper tension bound, or add it to the lower bound depending on the sign, then recompute the window width as a percentage. The illustrative arithmetic shows a window that shrinks as the temperature difference grows.
Check the window at both the minimum and maximum service temperature. A window checked only at the reference temperature can fail at either extreme.
| Environment question | Short answer | Derating factor | In this guide |
|---|---|---|---|
| What should be checked about multiplying individual factors into one product? | Combined derating multiplies the individual factors rather than averaging them. | Express humidity, temperature, cycle count and handling as fractions of the reference limit, then multiply … | Section 1 |
| What should be checked about keeping humidity, temperature and cycles separate? | Three derating mechanisms are computed separately before they are combined. | Humidity acts on moisture uptake, temperature on dimensional and stiffness change, and cycles on accumulated … | Section 2 |
| What should be checked about bounding the tension window with the … | A thermal mismatch narrows the usable tension window before any load is applied. | Subtract the absolute mismatch effect from the upper tension bound, or add it to the … | Section 3 |
| What should be checked about floor area per thousand reels? | Floor area per thousand reels turns a stored population into a comparable space figure. | Multiply the bounding-square footprint by the unit count, divide by the number of storable layers … | Section 4 |
Floor area per thousand reels turns a stored population into a comparable space figure.
Multiply the bounding-square footprint by the unit count, divide by the number of storable layers, then scale the result to one thousand reels. The output is square metres per thousand units.
Scaling to a fixed thousand makes a single-layer layout and a stacked layout directly comparable even when the fleet sizes differ.
Every load result must carry the case it was computed for.
Write the load case, the tension bound, the sheet thickness, the span and the unit system on the same line as the result. Without those five items the number cannot be compared with a later calculation.
A result without a case label is easily reused on a different lane or cable family where it does not apply.
The bottom layer governs the stack design because it carries every layer above it.
Multiply the unit mass by the layers above the bottom layer and add the contents of the bottom unit itself if they bear on the same path. Compare that result with the allowable load from the flange calculation.
Use the bottom-layer value in the margin ratio. An average across layers hides the peak and can pass a stack whose lowest units are already overloaded.
Combined derating multiplies the individual factors rather than averaging them. Express humidity, temperature, cycle count and handling as fractions of the reference limit, then multiply them and apply the product to the …
Three derating mechanisms are computed separately before they are combined. Humidity acts on moisture uptake, temperature on dimensional and stiffness change, and cycles on accumulated damage. Compute each factor from its own …
Floor area per thousand reels turns a stored population into a comparable space figure. Multiply the bounding-square footprint by the unit count, divide by the number of storable layers, then scale the result to one thousand …
The bottom layer governs the stack design because it carries every layer above it. Multiply the unit mass by the layers above the bottom layer and add the contents of the bottom unit itself if they …
References checked by publisher and title on 2026-11-17. Standards and regulations are cited by name only; no performance values are attributed to them. Every figure and every worked example in the text uses illustrative input values, not measured product data; substitute your own measured inputs and verify them against your supplier’s current data sheet and a trial before use. Confirm applicability and current versions for your own operation before relying on any of them.
For a quotation, a sample reel or help substituting your own cable diameter, winding length, stack height and return route into these calculations on site, contact service@mingplastics.com or WhatsApp +86 189 3887 1524. Include the cable type, the destination, the expected cycles per year and the figures your finance and sustainability teams need to defend so the recommended specification can be confirmed before you order.
For combined derating factor equation, Apply one derating factor per environmental variable and show the combined factor in the final line. The bottom layer governs the stack design because it carries every layer above it.