Address
Building 1, No. 22, Shexi Yongping Road,
Dongguan, Guangdong, China
Work Hours
Monday to Friday: 7AM - 7PM
Weekend: 10AM - 5PM
Address
Building 1, No. 22, Shexi Yongping Road,
Dongguan, Guangdong, China
Work Hours
Monday to Friday: 7AM - 7PM
Weekend: 10AM - 5PM
Low temperature load derating lowers an allowable stack or impact load for a stated minimum service temperature. Define the ... Ask Mingskye for a sample.
Low temperature load derating lowers an allowable stack or impact load for a stated minimum service temperature. Define the reference temperature, the minimum temperature and the property retention measured at that minimum, then multiply the reference load by the retention fraction. A worked example with illustrative values shows the reduction. Record the destination climate with the derated figure, and apply it as a separate factor from humidity and from cycle count.
This page covers low temperature load derating in six sections: Reel footprint from flange diameter; Counting cycles instead of months; Applying a packing factor to theoretical length; Plotting strain against exposure time; Multiplying coefficients by length and delta T; Listing every factor source with the result. Each section answers one practical question and can be read on its own.
The footprint of a stored reel is the square of its flange diameter, not its circular area.
A reel standing on its flange occupies the bounding square that its diameter defines, because the circular shape cannot share the corner space with a neighbouring reel. With an illustrative 400 mm flange the footprint is 0.16 square metres.
Use that bounding square in a floor area calculation. Using the circular area understates the space a block of reels actually needs.
A cycle count measures use, which a calendar month does not.
A reel on a busy lane may complete several cycles in a month while one held at a customer site completes none. Counting cycles keeps the retirement estimate attached to actual duty.
Record the cycle counter field that supplies the count. Without a reliable counter the estimator falls back to elapsed time and loses its main advantage.
For terminology and test-method context see ISO standards catalogue. The guidance on this page is practical handling guidance, not a test report or a certificate.
A packing factor corrects the geometric length for the gaps a real winding leaves behind.
Divide the sum of cable cross sections by the available window of traverse times radial build to obtain a dimensionless factor below one, then multiply the theoretical length by it. A level-wound pack and a poorly traversed pack produce visibly different factors on the same reel.
Measure the factor on a trial winding rather than borrowing one from another cable type. Cable stiffness, traverse pitch and tension all change how tightly a pack fills the window.
| Environment question | Short answer | Derating factor | In this guide |
|---|---|---|---|
| What should be checked about reel footprint from flange diameter? | The footprint of a stored reel is the square of its flange diameter, not its circular … | A reel standing on its flange occupies the bounding square that its diameter defines, because … | Section 1 |
| What should be checked about counting cycles instead of months? | A cycle count measures use, which a calendar month does not. | A reel on a busy lane may complete several cycles in a month while one … | Section 2 |
| What should be checked about applying a packing factor to theoretical … | A packing factor corrects the geometric length for the gaps a real winding leaves behind. | Divide the sum of cable cross sections by the available window of traverse times radial … | Section 3 |
| What should be checked about plotting strain against exposure time? | A creep curve plots strain against elapsed exposure rather than one final deformation. | Divide deformation at each time step by the initial dimension to obtain strain, then plot … | Section 4 |
A creep curve plots strain against elapsed exposure rather than one final deformation.
Divide deformation at each time step by the initial dimension to obtain strain, then plot strain against time at a stated relative humidity. The slope shows how fast the change is progressing.
Use a fixed time step across both materials. Uneven sampling makes the slopes incomparable.
Thermal change is a coefficient multiplied by a length and a temperature difference.
Multiply each coefficient by the relevant length and by the difference between the reference and service temperature. Keep all lengths in one unit and the temperature difference in one scale.
Record the coefficient source for the hub material and for the cable separately. A single generic coefficient erases the mismatch you are trying to compute.
A derated figure is only reproducible when each factor carries its source.
Print the test method, the sample, the exposure condition and the date beside every factor in the product. A combined value with no source list cannot be re-derived.
Version the whole line when one factor is refreshed. That keeps an old derated figure traceable to the tests that produced it.
The footprint of a stored reel is the square of its flange diameter, not its circular area. A reel standing on its flange occupies the bounding square that its diameter defines, because the circular shape cannot share the corner …
A cycle count measures use, which a calendar month does not. A reel on a busy lane may complete several cycles in a month while one held at a customer site completes none …
A creep curve plots strain against elapsed exposure rather than one final deformation. Divide deformation at each time step by the initial dimension to obtain strain, then plot strain against time at a stated relative …
A derated figure is only reproducible when each factor carries its source. Print the test method, the sample, the exposure condition and the date beside every factor in the product. A combined value with …
References checked by publisher and title on 2026-11-17. Standards and regulations are cited by name only; no performance values are attributed to them. Every figure and every worked example in the text uses illustrative input values, not measured product data; substitute your own measured inputs and verify them against your supplier’s current data sheet and a trial before use. Confirm applicability and current versions for your own operation before relying on any of them.
For a quotation, a sample reel or help substituting your own cable diameter, winding length, stack height and return route into these calculations on site, contact service@mingplastics.com or WhatsApp +86 189 3887 1524. Include the cable type, the destination, the expected cycles per year and the figures your finance and sustainability teams need to defend so the recommended specification can be confirmed before you order.
For low temperature load derating, Apply one derating factor per environmental variable and show the combined factor in the final line. A derated figure is only reproducible when each factor carries its source.